Axminster Trade AT340E Original Instructions Manual Download Page 2

Page: 2 / 28

Index of Contents

EU Declaration of Conformity

EU Declaration of Conformity

What’s Included

03-04-05-06

General Instruction for 230V Machines

Specific Safety for Dust Extractors

Specification 07
Assembly 08-09-10-11-12-13-14
Illustration and Parts Description

15-16-17

Operating Instruction

18-19

Ducting System

Maintenance 21
Weekly LEV System Maintenance Log

22-23

LEV Testing

Extraction Accessories

Exploded Diagrams/Parts Lists

25-26

Wiring Diagram

The symbols below advise the correct safety procedures when using this machine.

Fully read manual

and safety instructions

before use

Eye protection

should be worn

Ear protection

should be worn

HAZARD

Dust mask

should be worn

Cert No: CT-90HCK

Axminster Tools & Machinery Ltd
Axminster Devon
EX13 5PH UK
axminster.co.uk

Type

Dust Extractor

Model

AT340E

and conforms to the machinery example for which the
EC Type-Examination Certificate No 1002-CI-32016/META-2016002-A1
has been issued by META INTERNATIONAL CO., LTD
at: No. 117, In. 400.sec.3, Yatan td., Daya Dist., Taichung City 428, Taiwan

and complies with the relevant essential health and safety requirements.

2006/42/EC
2014/35/EU
EN ISO 12100:2010
EN 60204-1:2006+A1: 2009+AC:2010

declares that the machinery described:-

This machine complies with the following directives:

EU Declaration of Conformity

Signed

Andrew Parkhouse
Operations Director

Date: 03/05/2016

Summary of Contents for Trade AT340E





























Search results

Summary of Contents for Trade AT340E

Reviews:

Related manuals for Trade AT340E

Brands by name

Popular brands

Axminster Trade AT340E, Original Instructions Manual

Search results

Summary of Contents for Trade AT340E

Reviews:

Related manuals for Trade AT340E

Brands by name

Popular brands