background image

Index of Contents

Page No.

02

Declaration of Conformity

Index of Contents

02               

Declaration of Conformity

02

What’s in the Box

03

General Instructions for 230V Machines

03-04 

Specific Safety Instructions for Morticers

04

Unpacking and Assembly

05

Specifications

05

Illustration and Parts Description

06-07-08-09

Installing the Chisel and Bit

10

Operating Instructions

11

Maintenance

12

Parts Breakdown/List

13-14-15-16-17

Notes

18-19

Copied from CE Certificate

The undersigned,  

K. Bodenstein 

authorised by

Laizhou Tongtai Machinery Co.,Ltd.

Shilipu Chenggang Road, Laizhou, Shandong
261400 P.R. China declares that this product:

Model number

MS3840,  MS3840T     Morticer

manufactured by Laizhou Tongtai Machinery Co. in
compliance with the following standards or
standardisation documents in accordance with
Council Directives 

98/37/EC

Warning

The symbols below advise that you follow the correct
safety procedures when using this machine. 

Dust mask

should be worn

Ear protection

should be worn

Eye protection

should be worn

Fully read manual

and safety instructions

before use

HAZARD

Motor gets hot 

Summary of Contents for AW19FM





















Reviews: