manualshive.com logo in svg

Axminster Craft AC216TS, Original Instructions Manual

Share
Download
Axminster Craft AC216TS Original Instructions Manual Download Page 6

Optional Accessories

6

Quantity 

Item  

 

 

Part

 

1 

Table Insert for the AC216TS Code: 104933 

31

 

 

Table Insert for the AC254TS Code: 106807

 

1 

19mm Mitre Fence 

32

 

1 

Left Hand Extension Table with Long Rip Fence Rail/Scale AC216TS Code: 106808 

33

 

1 

Left Hand Extension Table with Long Rip Fence Rail/Scale AC254TS Code: 106809

28

31

32

29

30

The following will enable you to observe good working 
practices, keep yourself and fellow workers safe and maintain 
your tools and equipment in good working order. 

WARNING!! KEEP TOOLS AND EQUIPMENT
OUT OF REACH OF YOUNG CHILDREN

Mains Powered Tools
• Tools are supplied with an attached 13 Amp plug.
•  Inspect the cable and plug to ensure that neither are 

damaged. Repair if necessary by a suitably qualified person.

• Do not use when or where it is liable to get wet.  

Workplace

•  Do not use 230V a.c. powered tools anywhere 

within a site area that is flooded.

• Keep machine clean.
•  Leave machine unplugged until work is about to commence.
•  Always disconnect by pulling on the plug body and not the 

cable. 

•  Carry out a final check e.g. check the cutting tool 

is securely tightened in the machine and the correct 
speed and function set.

•  Ensure you are comfortable before you start work, 

balanced, not reaching etc.

•  Wear appropriate safety clothing, goggles, gloves, 

masks etc. Wear ear defenders at all times.

•  If you have long hair wear a hair net or helmet to prevent it 

being caught up in the rotating parts of the machine.

•  Consideration should be given to the removal of rings and 

wristwatches.

• Consideration should also be given to non-slip footwear etc.
•  If another person is to use the machine, ensure they are 

suitably qualified to use it.

•  Do not use the machine if you are tired or distracted 
•  Do not use this machine within the designated safety areas 

of flammable liquid stores or in areas where there may be 
volatile gases.

•  Check cutters are correct type and size, are undamaged 

and are kept clean and sharp, this will maintain their  
operating performance and lessen the loading on the 
machine. 

•  OBSERVE….  make sure you know what is happening 

around you and USE YOUR COMMON SENSE.

KEEP WORK AREA AS UNCLUTTERED AS IS PRACTICAL. 
UNDER NO CIRCUMSTANCES SHOULD CHILDREN BE 
ALLOWED IN WORK AREAS.

General Instructions for 230V Machines

33

Summary of Contents for AC216TS









































Reviews:

No comments

Brands by name

Popular brands

Load more brands