manualshive.com logo in svg

Axminster Craft AC216TS, Original Instructions Manual

Share
Download
Axminster Craft AC216TS Original Instructions Manual Download Page 23

Set Up and Adjustment

23

‘T’ Slot

E

2. The rip fence extension can be repositioned from the vertical 
to a horizontal position for guiding thin pieces through. Loosen 
the two butterfly knobs holding the fence extension, remove, 
lay the fence extension down in the horizontal position and 
remount the fence extension as before, see fig 79-80. Move
the extension down until the end face is centred with the
blade and tighten the two butterfly knobs.

Fig 79-80

Adjusting the Cutting Height

Release the clamping knob, adjust the blade height with the
rise and fall operating wheel, see fig 81, so that the blade teeth 
are protruding through the work piece.

Fig 81

Adjusting the Pivot

Release the locking knob to the centre of the operating wheel 
(a) to the side of the saw assembly and turn clockwise to pivot 
the saw to a maximum of 45˚ degrees, indicated on the scale, 
see fig 82-83-84.

Clamping knob

Fig 82-83-84

a

Saw pivot scale

45˚

Summary of Contents for AC216TS









































Reviews:

No comments

Brands by name

Popular brands

Load more brands