manualshive.com logo in svg

Axminster Craft AC125BDS, Original Instructions Manual, Page: 2 / 20

Share
Download
Axminster Craft AC125BDS Original Instructions Manual Download Page 2

Index of Contents

2

EU Declaration of Conformity 

03

What’s Included 

03

General Instructions for 230V Machines  

04

Specific to Sanding Machines  

04-05

Specification  

05

Assembly  

06-07-08

Setting Up  

08-09-10-11 

Sanding Configurations  

11

Illustration and Parts Description  

12-13 

Changing the Abrasive Belt/Disc  

14

Maintenance  

15

Trouble Shooting  

15

Exploded Diagrams/Lists  

16-17-18

Wiring Diagram  

19

EU Declaration of Conformity

Fully read manual

and safety instructions

before use

Eye protection

should be worn

Ear protection

should be worn

HAZARD

Motor gets hot

Dust mask

should be worn

The symbols below advise the correct safety procedures when using this machine.

Cert No:  MM411

Axminster Tools & Machinery Ltd
Axminster Devon 
EX13 5PH UK
axminster.co.uk

Type

Mini Belt & Disc Sander

Model

AC125BDS

and conforms to the machinery example for which the 
EC Type-Examination Certificate No N8M 15 09 41469 776
has been issued by Jiangsu Jinfeida Power Tools Co., Ltd.
at: Xiejia Town, 225644 Gaoyou City, Jiangsu Province, People’s Republic of China

and complies with the relevant essential health and safety requirements. 

2006/42/EC
2006/95/EC
EN 61029-1: 2009/A11: 2010
EN ISO 12100: 2010

declares that the machinery described:-

This machine complies with the following directives:

EU Declaration of Conformity

Signed

Andrew Parkhouse
Operations Director

Date: 14/10/2015 

Summary of Contents for AC125BDS





















Reviews:

No comments