manualshive.com logo in svg

Axis T8504-E, User Manual

Share
Download
Axis T8504-E User Manual Download Page 21

AXIS T8504–E Outdoor PoE Switch

SysLog Message

7

Unit configuration changed

is

sent when the unit configuration is
changed.

9

PoE controller reset

is sent when

PoE controller reset occurs.

10

PoE controller has no firmware

is

sent when PoE controller firmware
is erased or is corrupted.

11

Invalid SSH

is sent when a remote

user tries to access the unit by
SSH with incorrect username or
password.

Remote user IPv4/IPv6 address

12

DHCPv4

is sent only the first time

DHCPv4 address is obtained either
by switching from static to DHCPv4
or on power-up.

• Unit hostname
• Unit MAC address
• DHCPv4 address

Message is sent in broadcast format
255.255.255.255 to any SysLog
server connected over LAN and to
SysLog server 1 and 2.

13

DHCPv6

is sent only the first time

DHCPv6 address is obtained either
by switching from static to DHCPv6
or on power-up.

• Unit hostname
• Unit MAC address
• DHCPv6 address

Message is sent in broadcast format
255.255.255.255 to any SysLog
server connected over LAN and to
SysLog server 1 and 2.

14

Invalid VLAN configuration

is sent when the unit upon
power-up detects that current VLAN
configurations prevent the unit from
being managed over the network.
This is possibly due to a faulty new
configuration file being uploaded
to the unit. The unit restores itself
to semi factory default, turns off
VLAN and restores most of its
configuration parameters to factory
default, leaving the unit’s network
IP parameters unchanged. Then the
unit restarts.

Message is sent in broadcast format
255.255.255.255 to any SysLog
server connected over LAN and to
SysLog server 1 and 2.

21

Summary of Contents for T8504-E

























Reviews:

No comments

Brands by name

Popular brands

Load more brands