Axis Q1635 Installation Manual Download Page 22

AXIS Q1635 Network Camera

Safety instructions

NO

NO

NOTICE

TICE

TICE

• The Axis product shall be used in compliance with local laws and regulations.

• Axis recommends using a shielded network cable (STP) CAT5 or higher.

• To use the Axis product outdoors, or in similar environments, it shall be installed in an

approved outdoor housing.

• Store the Axis product in a dry and ventilated environment.

• Avoid exposing the Axis product to shocks or heavy pressure.

• Do not install the product on unstable poles, brackets, surfaces or walls.

• Use only applicable tools when installing the Axis product. Using excessive force with

power tools could cause damage to the product.

• Do not use chemicals, caustic agents, or aerosol cleaners.

• Use a clean cloth dampened with pure water for cleaning.

• Use only accessories that comply with the technical specification of your product. These

can be provided by Axis or a third party. Axis recommends using Axis power source
equipment compatible with your product.

• Use only spare parts provided by or recommended by Axis.

• Do not attempt to repair the product yourself. Contact Axis support or your Axis reseller

for service matters.

• The power supply shall be plugged in to a socket outlet installed near the product and

shall be easily accessible.

• Use a limited power source (LPS) with either a rated output power limited to

100 W or a

rated output current limited to

5 A.

Transportation

NO

NO

NOTICE

TICE

TICE

• When transporting the Axis product, use the original packaging or equivalent to prevent

damage to the product.

Battery

The Axis product uses a 3.0 V CR2032 lithium battery as the power supply for its internal real-time
clock (RTC). Under normal conditions this battery will last for a minimum of five years.

Low battery power affects the operation of the RTC, causing it to reset at every power-up. When
the battery needs replacing, a log message will appear in the product’s server report. For more
information about the server report, see the product´s setup pages or contact Axis support.

22

Summary of Contents for Q1635

























Reviews: