Axis M1114-E User Manual Download | Manualshive

Page: 6 / 55

background image

AXIS M1114–E

Hardware Overview

Hardware Overview

4

5

7

8

6

1

2

3

9

1.

Network LED

2.

Status LED

3.

Power LED

4.

Iris connector

5.

Network connector

6.

Control button

7.

Zoom puller

8.

Focus puller

9.

Screw holding CS ring

Connectors and Buttons

For technical specifications, see

Network Connector

RJ45 Ethernet connector with Power over Ethernet (PoE).

NO

NO

NOTICE

TICE

TICE

The product shall be connected using a shielded network cable (STP). All cables connecting the product to the network shall
be intended for their specific use. Make sure that the network devices are installed in accordance with the manufacturer’s
instructions. For information about regulatory requirements, see

Electromagnetic Compatibility (EMC) on page 2

.

Control Button

For location of the control button, see

Hardware Overview on page 6

The control button is used for:

•

Resetting the product to factory default settings. See

.

•

Connecting to an AXIS Video Hosting System service. See

. To connect, press and hold the button for about 3

seconds until the Status LED flashes green.

•

Connecting to AXIS Internet Dynamic DNS Service. See

. To connect, press and hold the button for about 3 seconds.

6

«
...
4
5
6
7
8
...
»

Summary of Contents for M1114-E
























































Reviews:

No comments

Related manuals for M1114-E

Brand: Ultrative Pages: 9

Brand: Idis Pages: 2

Brand: 3xLogic Pages: 25

VX-2A-B-IWD (R)

Brand: 3xLogic Pages: 80

DeltaSphere-3000

Brand: 3rdTech Pages: 9

MES ACURAS HEAD

Brand: Barco Pages: 131

CAMEDIA C-60 Zoom

Brand: Olympus Pages: 2

Brand: Canon Pages: 132

CAMEDIA C-5500 Sport Zoom

Brand: Olympus Pages: 2

FE 370 - Digital Camera - Compact

Brand: Olympus Pages: 70

FE 370 - Digital Camera - Compact

Brand: Olympus Pages: 70

Brand: Olympus Pages: 68

Brand: Digimerge Pages: 2

Brand: Dahua Technology Pages: 15

Brand: Hitron Pages: 71

Brand: DSE Pages: 2

Bike Guardian Wi-Fi

Brand: Midland Pages: 46

IPC-HUM4231S-L4-0280B-S3

Brand: Dahua Technology Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands