AXIOMTEK CAPA520 User Manual Download

Page: 18 / 75

CAPA520 Intel

Core

Processor Family 3.5

” Board

Board and Pin Assignments

2.5

Connectors

Signals go to other parts of the system through connectors. Loose or improper connection
might cause problems, please make sure all connectors are properly and firmly connected.
Here is a summary table of connectors on the hardware.

Connector

Description

CN1

Front Panel Connector

CN2

SMBus Connector

CN3

HDMI Connector

CN4

DisplayPort Connector

CN5

Inverter Connector

CN6

LVDS Connector

CN7, CN8

Ethernet Port 1 and 2

CN9

Ethernet Port 3 Wafer Connector

CN10

USB 3.0 Port

CN11

USB 3.0/USB2.0 Port

CN12

USB 2.0 Wafer Connector

CN13, CN14

SATA 0 and 1 Ports

CN15, CN16

SATA 0 and 1 Power Connectors

CN17

COM1 Wafer Connector

CN18

Fan Connector

CN19

Digital I/O Connector

CN20

Audio HDA Wafer Connector

ATX1

ATX Power Connector

BAT1

CMOS Battery Connector

SCN1

Full-size PCI-Express Mini Card Connector

SCN2

SIM Card Wafer Connector

SCN3

ZIO Expansion Connector

SDIMM1

DDR4 SO-DIMM Connector

Summary of Contents for CAPA520












































































Search results

Summary of Contents for CAPA520

Reviews:

Related manuals for CAPA520

Brands by name

Popular brands

AXIOMTEK CAPA520, User Manual

Search results

Summary of Contents for CAPA520

Reviews:

Related manuals for CAPA520

Brands by name

Popular brands