AXIOMTEK AIE900-XNX Series User Manual Download

Page: 49 / 53

AIE900-XNX Series U

ser’s Manual

Jetpack SDK Flash Guide

SECTION 4

JETPACK SDK Flash Guide

This section provides users with a detailed description of how to flash NVIDIA JetPack SDK for
AIE900-XNX. Users can follow the instructions below to install or reinstall JetPack SDK by
themselves.

4.1

JETPACK FLASH METHOD

Please use the following instructions to flash the JetPack to the AIE900-XNX.

Please contact our sales or FAE for the latest Jetpack SDK, and prepare a Linux
host system running x86_64 Ubuntu v16.04

Note:

If the Linux host system is running x86_64 Ubuntu v18.04, please follow

the instructions below to install Python first.

Step 1. Connect the Linux host system to internet

Step 2. Install Python with the command below:

sudo apt-get update

sudo apt-get install python

Step1. Set up the AIE900-XNX connection as follows:

⚫

Connect a USB cable from the Linux host system to the Micro USB port on

AIE900-XNX, and switch the recovery switch to ON. For more details,
please refer to 3.3.13 Recovery Mode Switch (SSW1).

⚫

Connect an HDMI monitor to AIE900-XNX.

Summary of Contents for AIE900-XNX Series






















































Search results

Summary of Contents for AIE900-XNX Series

Reviews:

Related manuals for AIE900-XNX Series

Brands by name

Popular brands

AXIOMTEK AIE900-XNX Series, User Manual

Search results

Summary of Contents for AIE900-XNX Series

Reviews:

Related manuals for AIE900-XNX Series

Brands by name

Popular brands