AXIOMTEK AIE900-902-FL Series User Manual Download Page 47

Page: 47 / 51

AIE900-902-FL Series U

ser’s Manual

Jetpack BSP Flash Method

SECTION 4

JETPACK SDK Flash Guide

This section provides users with a detailed description of how to flash NVIDIA JetPack SDK for
AIE900-902-FL. Users can follow the instructions below to install or reinstall JetPack SDK by
themselves.

4.1

JETPACK FLASH METHOD

Please use the following instructions to flash the JetPack to the AIE900-902-FL.

Please contact our sales or FAE for the latest Jetpack SDK , and prepare a Linux
host system running x86_64 Ubuntu v16.04

Note:

the Linux host system is running x86_64 Ubuntu v18.04, please

follow the instructions below to install Python first.

Step 1. Connect the Linux host system to internet

Step 2. Install Python with the command below:

sudo apt-get update

sudo apt-get install python

Step1. Set up the AIE900-902-FL connection as follows:

⚫

Connect a USB cable from the Linux host system to the Micro USB port on

AIE900-902-FL, and switch the recovery switch to ON. For more details,
please refer to 3.2.17 Recovery Mode Switch (SSW2).

⚫

Connect an HDMI monitor to AIE900-902-FL.

Summary of Contents for AIE900-902-FL Series




















































Search results

Summary of Contents for AIE900-902-FL Series

Reviews:

Related manuals for AIE900-902-FL Series

Brands by name

Popular brands

AXIOMTEK AIE900-902-FL Series, User Manual

Search results

Summary of Contents for AIE900-902-FL Series

Reviews:

Related manuals for AIE900-902-FL Series

Brands by name

Popular brands