background image

 

iv 

Classification 

 

1. 

Degree of production against electric shock: not classified  

2. 

Equipment  not  suitable  for  use  in  the  presence  of  a  flammable  anesthetic 
mixture with air or with oxygen or nitros oxide.  

3. 

Mode of operation: Continuous  

4. 

Type of protection against electric shock: Class I equ ipment 

 

General Cleaning Tips 

You  may  need  to  take  the  following  precautions  before  you  begin  to  clean  the 
computer.  When  you  clean  any  single  part  or  component  for  the  com puter,  please 
read and understand the details below fully. 

 

When you need to clean the device, please rub it with a piece of dry  cloth. 

1. 

Be cautious of the tiny removable components when  you use a vacuum cleaner 
to absorb the dirt on the floor.  

2. 

Turn the system off before you start to clean up t he component or computer. 

3. 

Never  drop  the  components  inside  the  computer  or  get  circuit  board  damp  or 
wet. 

4. 

Be  cautious  of  all  kinds  of  cleaning  solvents  or  chemicals  when  you  use  it  for 
the sake of cleaning. Some individuals may be allergic to the ingredien ts. 

5. 

Try not to put any food, drink or cigarette around the computer.  

 

Summary of Contents for Agent200
























Reviews: