manualshive.com logo in svg

Axel TIGER E5, User Manual, Page: 5 / 163

Share
Download
Axel TIGER E5 User Manual Download Page 5

 
 

 

 

5 

SAFETY WARNINGS/ISTRUZIONI PER LA SICUREZZA |FOREWORD 

TIGER E5 · User Manual · ENG 

 

 

FOREWORD 

 
_____________________________________________________________________________________________________________________ 

For your own safety and to avoid invalidation of the warranty all text marked with these Warning Symbols should be read carefully. 

 

_____________________________________________________________________________________________________________________ 

Information in this manual is subject to change without notice and does not represent a commitment on the part of the vendor. 

 

The manufacturer shall not be liable for any loss or damage whatsoever arising from the use of information or any  error contained in this manual, or through any mis-operation or 
fault in hardware contained in the product. 

 

It is recommended that all maintenance and service on the product should be carried out by the manufacturer or its authorised agents. The manufacturer cannot accept any 
liability whatsoever for any loss or damage caused by service, maintenance or repair by unauthorised personnel 

 

 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for TIGER E5




































































































































































Reviews:

No comments