manualshive.com logo in svg

AWH DN10, Operating Instructions Manual, Page: 14 / 28

Share
Download
AWH DN10 Operating Instructions Manual Download Page 14

11/13

Inline Sight Glass

Operating Instructions

17

4.2 Labelling the Inline Sight Glass

The information in these operating instructions only applies to the inline sight glass of the type and 

version specifi ed on the title page.

If you have any queries, specify the following correctly:

- the nominal width

- the sealing material

- the housing material

This is the only way to ensure effi cient, quick processing.

4.3 Safety Measures (to be carried out by operator)

Note that

-  The operator is responsible for training its operating and maintenance personnel and monitoring 

  compliance with safety measures, including the obligation to wear personal protective equipment.

-  The operator shall ensure that unauthorised persons (not operating or maintenance personnel) are 

prevented from entering the hazardous area of the machine (in which the inline sight glass is installed). 

-  The inline sight glass may only be installed or serviced if the pipelines have been previously drained.

-  The separation of energy sources shall be designed technically to enable compliance with the shut-

down procedures described in section 5.4.

These operating instructions shall be retained for future use. 

They must be available in the vicinity of the system in which the inline sight glass is installed.

The frequency of inspections and monitoring measures shall be observed.

The work described in the sections on

 transport, installation, assembly, maintenance, malfunction /

cause / remedy 

shall only be carried out by experts.

Expert

A person with appropriate training, suitable instruction and experience who is in a position to identify 

risks and avoid hazards.

4.4 Operator's Duties

Note

In the EEA (European Economic Area), the national implementations of the frame-

work directive (89/391/EEA) and the associated individual directives, especially 

the directive (2009/104/EC) on the minimum specifi cations for safety and health 

protection of employees using work equipment, shall be observed and complied 

with in their current valid versions. In Germany, the 2011 Ordinance on Industrial 

Safety and Health (BetrSichV) shall be observed.

Summary of Contents for DN10





























Reviews:

No comments