AVZ Twins Piazzola Installation Instruction Download Page 12 | Manualshive

Page: 12 / 20

background image

Twins Piazzola EN 27-08-2018

Page 12

Assembly instructions Twins

®

Piazzola

®

Butterfly awning

7.

Attach the side plates to the support beam.

8.

Attach the legs to the foundations and make sure they are level.

9.

Insert the support beam with side plates in the legs and fasten them.

10.

Place the strut between the leg and support beam. Draw the holes and drill holes of 9 mm.

11.

Fasten the strut with M8 bolts and check that the structure is level.

«
...
10
11
12
13
14
...
»

Summary of Contents for Twins Piazzola





















Reviews:

No comments

Related manuals for Twins Piazzola

Brand: Samsung Pages: 88

Brand: Samsung Pages: 215

Brand: AA Products Pages: 8

Brand: 3Doodler Pages: 24

Brand: Abus Pages: 2

Brand: Bang & Olufsen Pages: 12

Brand: KDS Pages: 72

Wormhole Station JUH-320

Brand: J5create Pages: 24

Brand: La Crosse Technology Pages: 2

Brand: La Crosse Technology Pages: 2

Brand: La Crosse Pages: 2

Brand: Uebler Pages: 18

Brand: Carefree Pages: 12

Brand: Aroflora Pages: 36

OADM 21I6480/S14F

Brand: Baumer Pages: 4

Brand: Enviro Pages: 4

Brand: EGO Pages: 2

Transit Vancouver Wagon

Brand: Webasto Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands