SPECIFICATIONS
Model:
AVP-AV-1S-C
1
Maximum amplitude
2
:
< 1 to 5 V
Pulse width (FWHM):
0.2 - 4 ns
PRF:
100 Hz to 1 MHz
Rise time (20%-80%):
≤ 80 ps
Fall time (80%-20%):
≤ 200 ps
Polarity:
Specify -P, -N, -PN
Required load impedance:
50 Ohms
5
Accuracy / calibration:
Not calibrated. At lower pulse widths and higher PRFs, the amplitude tends to
roll off relative to the set value. For high-accuracy applications requiring
traceable calibration, verify the output with a calibrated oscilloscope.
Propagation delay:
≤ 200 ns (Ext trig in to pulse out)
Jitter, Ext trig in to pulse out:
± 35ps ± 0.015% of sync delay
Trigger modes:
Internal trigger, or external trigger (TTL level pulse, > 50 ns, 1 kΩ input impedance)
Variable delay:
Sync to main out: 0 to 200 ns, for internal trigger mode only.
No variable delay in external trigger mode
Sync output:
+3 Volts, > 50 ns, will drive 50 Ohm loads
DC offset or bias insertion:
Optional
3
. Apply required DC offset or bias in the range of ± 50V (250 mA max)
to back panel solder terminal.
Monitor output option
4
:
Provides a 20 dB (x10) attenuated coincident replica of main output
Connectors:
Out, Monitor: SMA. TRIG, SYNC, GATE (-B only): BNC
Optional accessory kit:
(attenuators and terminators)
Add the suffix "-AK1" to the model number to include the recommended accessory kit. Consists of
three SMA, 18 GHz, 2 Watt attenuators (10, 20 & 30 dB) for use on the output, and two 50 Ohm,
1 GHz, 1 Watt feed-through terminators (one SMA, one BNC) for use on external trigger inputs.
Optional accessory kit:
(coaxial cables and adapters)
Add the suffix "-AK8" to the model number to include the recommended accessory kit.
Consists of one 12-inch SMA-M/SMA-M PE-SR405FL coaxial cable, one 12-inch SMA-M/SMA-M RG-
316 coaxial cable, one 36-inch SMA-M/SMA-M RG-316 coaxial cable, one 24-inch SMA-M/BNC-M RG-
316 coaxial cable, one 36-inch BNC-M/BNC-M RG58C/U coaxial cable, one SMA-F to BNC-M adapter,
one SMA-M to BNC-F adapter, one SMA-F to SMA-F adapter, and one SMA-F to solder cup adapter
Temperature range:
+5°C to +40°C
Power requirements:
100 - 240 Volts, 50 - 60 Hz
Dimensions:
100 × 430 × 375 mm (3.9” × 17” × 14.8”)
Chassis material:
Aluminum, with vinyl trim
1.
-C suffix indicates stand-alone lab instrument with internal clock and line powering. No suffix indicates miniature module requiring DC power and external
trigger. (See
http://www.avtechpulse.com/formats
for details of the four basic instrument formats).
2.
For operation at amplitudes of less than 20% of full-scale, best results will be obtained by setting the amplitude near full-scale and using external
attenuators on the output.
3.
For externally applied DC offset option suffix model number with -OS. The Avtech AVX-T bias tee can also be used to obtain DC offset. For internally
generated DC offset option (0 to ±5V) add the suffix -OT to the model number.
4.
For monitor option add suffix -M.
5.
A 50 Ohm load is required. Other loads may damage the instrument. Consult Avtech ([email protected]) if you need to drive other load impedances.
7
Summary of Contents for AVP-AV-1S-C
