Avtech AVP-AV-1S-C Instructions Manual Download Page 4

Page: 4 / 30

MECHANICAL INFORMATION......................................................................................22

TOP COVER REMOVAL.......................................................................................................22

ELECTROMAGNETIC INTERFERENCE..............................................................................22

MAINTENANCE..............................................................................................................23

REGULAR MAINTENANCE..................................................................................................23

CLEANING............................................................................................................................ 23

WIRING DIAGRAMS.......................................................................................................24

WIRING OF AC POWER.......................................................................................................24

PCB 158R5 - LOW VOLTAGE POWER SUPPLY................................................................25

PCB 235C - HIGH VOLTAGE DC POWER SUPPLY...........................................................26

PCB 126D - OSCILLATOR AND TRIGGER CIRCUIT..........................................................27

PCB 231A - INTERNAL OFFSET GENERATOR.................................................................28

MAIN WIRING.......................................................................................................................29

PERFORMANCE CHECK SHEET.................................................................................30

Manual Reference: /fileserver2/officefiles/instructword/avp/AVP-AV-1S-C,ed10.odt.

Last modified November 5, 2021.

Summary of Contents for AVP-AV-1S-C































Search results

Summary of Contents for AVP-AV-1S-C

Reviews:

Brands by name

Popular brands

Avtech AVP-AV-1S-C, Instructions Manual

Search results

Summary of Contents for AVP-AV-1S-C

Reviews:

Brands by name

Popular brands