Avtech AVOZ-D2-B, Instructions Manual

Page: 7 / 48

SPECIFICATIONS
Model 1 : AVOZ-D2-B
Amplitude 2 :
voltage (each output):
current (sum of all outputs):
0 to 700V
0 to 70A
Minimum load impedance:
(parallel combination of loads on all
outputs)
10 Ω
(Must be non-inductive
3
.)
Maximum number of 50Ω loads (if
outputs used separately):
5
Pulse width: 200 ns - 10 us
Rise time (20%-80%): < 100 ns
Fall time (80%-20%): < 100 ns
Maximum PRF: 2.5 kHz
Duty cycle: (max)
0.05%
Output impedance: < 0.4 Ohms
Average output power: 25W maximum
Droop: < 5%, at maximum pulse width and maximum amplitude
Polarity 4 : Positive or negative or dual-polarity (specify)
GPIB & RS-232 control 1 : Standard on -B units.
See http://www.avtechpulse.com/gpib for details.
LabView drivers: Check http://www.avtechpulse.com/labview
for availability and downloads
Propagation delay: < 200 ns (Ext trig in to pulse out)
Jitter: ± 100 ps ± 0.03% of sync delay (Ext trig in to pulse out)
Trigger required: External trigger mode: + 5 Volts, 50 to 500 ns (TTL)
Sync delay: Variable, 0 to ±1.0 seconds (sync out to pulse out)
Sync output: + 3 Volts, 100 ns, will drive 50 Ohm loads
Gate input: Synchronous or asynchronous, active high or low, switchable.
Suppresses triggering when active.
Output connectors:
(see above for quantity) Mainframe: Multiple SMA female connectors, for connection to an equal number of
separate 50 Ohm loads, or for connection to the output module.
Output module (if ordered): Multiple SMA female connectors for connection to
mainframe, and one Type-N female connector for connection to a low
impedance load.
Number of output connectors: 5
Optional cable kit:
(RG58C/U cables,
5 feet / 152 cm)
5 cables. Add -CK5 to model number.
Optional output module (for combining
multiple outputs on to a single Type-N
connector):
Add -OM5 to the model number.
Other connectors: Trig, Gate, Sync: BNC
Power, temperature:
100 - 240 Volts,
50 - 60 Hz.
Dimensions: Mainframe: 100 x 430 x 375 mm (3.9 x 17 x 14.8”),
-OM20 optional output modules: 43 mm x 66 mm x 107 mm (1.7” x 2.6” x 4.2”)
Chassis material: Anodized aluminum, with blue plastic trim
Temperature range: +5°C to +40°C
1) -B suffix indicates IEEE-488.2 GPIB and RS-232 control of pulse amplitude, pulse width, delay and PRF. (See http://www.avtechpulse.com/gpib).
2) For operation at voltage amplitudes of less than 10% of full-scale, better results may be obtained by setting the amplitude near full-scale and increasing the load
impedance accordingly. This will provide lower output currents.
3) For applications where additional resistance must be added in series with the device under test, Avtech recommends connecting multiple Ohmite (www.ohmite.com) OY-
series ceramic composition resistors in parallel to create a high-power, low-inductance effective resistance. These resistors can be purchased readily at http://www.digi-
key.com.
4) Indicate desired polarity by suffixing model number with -P or -N (i.e. positive or negative) or -PN for dual polarity option.
7