Avnet Xilinx Zynq 7Z045 Manual Download Page 25 | Manualshive

Page: 25 / 36

background image

Page 25

The following tables provide the 7Z045 pin assignments for the Ethernet PHY interface.

Table 11

– Ethernet PHY Pin Assignments

2.5.2

USB UART

The Zynq 7Z045 Mini-Module Plus Development Board implements a Silicon Labs CP2103
device that provides a USB-to-RS232 bridge. The USB physical interface is brought out on a
USB Micro-AB connector

labeled “J4”.

The USB UART interface connects to the 7Z045 at the following pins:

Net Name

7Z045 Pin #

USB_UART_RXD

C19

USB_UART_TXD

D18

Table 12

– USB UART Pin Assignments

2.5.3

USB 2.0 On-the-Go (OTG)

The Zynq 7Z045 Mini-Module Plus Development Board implements a

SMSC USB3320

USB 2.0

PHY that has the ability to operate in host mode (OTG) or as an endpoint device. The USB3320
device is interfaced to the outside world via the USB Micro-A-

B connector “J3” on the board. In

addition to the built-in ESD protection the USB3320 offers there are added ESD protection diodes
on-board to protect against electrostatic discharge when plugging in a USB cable.

Two jumpers allow the switching of device modes from OTG (Host) mode or endpoint mode.
The USB 2.0 circuit ships in endpoint mode by default. To switch the device into OTG mode
JP11 must be moved to the 2-3 position and JP7 must be placed.

The USB3320 device also offers over current detection/protection when in OTG

mode. “U16”

provide the 7Z045 with an OC signal that asserts LOW when an over-current condition exists.

The USB3320 device is powered from 1.8 V and is clocked at 26 MHz via “Y3”.

Resetting the USB 2.0 PHY can be done two ways. The USB_RESET# signal is wire ORed
(active low) by an I/O pin on the 7Z045 and the power-on reset circuit. To reset the USB PHY
via the 7Z045 I/O pin toggle pin A18 LOW. To reset the USB PHY via the power-on reset circuit
press SW2. See section 2.7 for details about the power-on reset circuit.

Net Name

7Z045 Pin #

ETH _RST#

B24 or SW1

ETH _RX_CTRL

G20

ETH_RX_CLK

L20

ETH _RX_D0

J21

ETH _RX_D1

M19

ETH _RX_D2

G19

ETH _RX_D3

M17

Net Name

7Z045 Pin #

ETH_MDC

D19

ETH _MDIO

C18

ETH _TX_CTRL

ETH_TX_CLK

L19

ETH _TX_D0

K21

ETH _TX_D1

K20

ETH _TX_D2

J20

ETH _TX_D3

M20

«
...
23
24
25
26
27
...
»

Summary of Contents for Xilinx Zynq 7Z045





































Reviews:

No comments

Related manuals for Xilinx Zynq 7Z045

Brand: Lattice Semiconductor Pages: 30

Brand: Eaton Pages: 16

Brand: Jands Pages: 6

Brand: U.S. Divers Pages: 22

Brand: xpr Pages: 4

Brand: Bettis Pages: 18

MURPHYMATIC ASM160

Brand: Murphy Pages: 4

VARIOMATIC SARV 07.1

Brand: AUMA Pages: 32

Brand: J+J Pages: 6

Brand: Wavelength Electronics Pages: 17

Brand: Rauch Pages: 85

CC2530-CC2592EM

Brand: Texas Instruments Pages: 3

TITAN Controls Saturn 4

Brand: Sunlight Supply Pages: 4

Brand: VistaLab Pages: 20

Hauser COMPAX-M Series

Brand: Parker Pages: 84

Brand: Danfoss Pages: 44

Brand: Dasko Electronic Pages: 4

Brand: Taco Electronic Solutions Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands