background image

 

2.6

 

Set operating mode 

 

permanent:

 When switched on using the mains switch (13), the unit is permanently ready to 

operate until it is switched off with the mains switch. 

automatic:

  The  amplifier  switches  on  automatically  as  soon  as  a  connected  pre-amplifier 

delivers an audio signal to one of the analog inputs (7, 8).  Standby mode is activated as soon 
as the pre-amplifier has not delivered a signal for more than 10 minutes. 

trigger:

 Switching to operating mode and to standby is controlled via the trigger input (10). 

For details, see section 1.6. 

remote: 

If you happen to use an AVM model of the PA or SD series as a pre-amplifier, your 

MA / SA 6.2 can be automatically switched on and off via inaudible digital signals sent over a 
connected  audio  cable  –  without  the  need  for  an  additional  trigger  cable.  In  addition,  the 
display brightness can also be remotely controlled – according to the selected setting on the 
pre-amplifier (see section 2.4).

 

 

2.7

 

Define load impedance 

 
To  obtain  correct  values  in  the  power  display  (see  2.5),  it  is  necessary  to  select  the given 
impedance according to your speakers (4 or 8 Ohms). This setting is only for calibrating the 
power display and has no influence on the performance of the amplifier itself. 
 
 
 
 

3

 

Reset (Factory settings) 

 
The 

Reset

 menu cancels certain or all settings and makes the unit return to default settings. 

 
To enter the 

Reset

 menu, please switch off your device on the rear of the unit at the mains 

switch (13). Keep the middle key under the display pressed (3) while you switch on the unit 
again (13). As soon as the display shows the reset menu

 

you can

 

release the multifunctional 

button under the display (3). Now press 

ALL

 to reset the unit completely. 

CANCEL

 will bring 

the unit back to normal operating mode without resetting any item. 
 
After  resetting  your  MA  /  SA  6.2,  the  unit  needs  to  be  restarted  at  the  mains  switch  (13). 
Switch off the unit, wait for a couple of seconds and turn it on again to complete the reset 
procedure.

 

4

 

Appendix 

4.1

 

Cleaning 

 

Use a soft cloth and normal glass cleansing fluid. 

 

CAUTION

  

Make sure no fluid gets into the unit. Do not use scouring cleaners. They may damage the 
surface. 
 
 

 

Summary of Contents for OVATION MA 6.2













Reviews: