manualshive.com logo in svg

AVM B1 v3.0, Manual, Page: 17 / 111

Share
Download
AVM B1 v3.0 Manual Download Page 17

Installation in Windows 2000

ISDN-Controller B1 v3.0 – 3 Installation in Windows 2000

17

3 Installation in Windows 

2000

In Microsoft Windows 2000, the AVM ISDN-Controller B1 v3.0
can be installed with the drivers included in the operating
system software. In this case, the drivers must be updated
using the latest drivers available either on the CD included in
the controller package or from the AVM Data Call Center
(ADC). This manual describes the other installation option:
installing the ISDN-Controller B1 v3.0 using the updated CAPI
2.0 drivers supplied on the controller CD. 

The CAPI 2.0 included in the package supports both 16-bit
and 32-bit applications. Applications in DOS windows are
not supported. For more information about CAPI, see the
section “The Applications Interface CAPI 2.0” on page 78.

Before beginning with the software installation, check that
the ISDN-Controller has been installed in the computer prop-
erly. Make sure that an I/O address available in the computer
is set on the ISDN-Controller (see the section “Setting the I/O
Address” on page 14).

The procedures described in this chapter  are  valid for  both
Windows 2000 Server and Windows 2000 Professional.

3.1 Installing the Driver Software

Note that administrator rights are required to perform the in-
stallation in Windows 2000.

Proceed as follows:

1.

Start Windows 2000.

2.

Insert the “AVM ISDN-Controller B1 v3.0” CD in your CD-
ROM drive. 

3.

Open the Windows 2000 Start menu and select the
“Run” command. In the command line, enter the path
to the installation program:

HB_B1V30.book  Seite 17  Mittwoch, 7. Februar 2001  3:19 15

Summary of Contents for B1 v3.0
















































































































Reviews:

No comments