background image

17 

3

 

Appendix 

 
 

3.1

 

Care of the housing 

 
The surface and the printing on the housing are largely scratch-resistant. The A 30.3 can be 
cleaned with mild soapy water or a gentle glass cleaner and a soft duster. 

 

ATTENTION: 

Do  not  allow  any  liquid  to  enter  the  inside  of  the  housing  during  cleaning.  In 

addition, for safety reasons, the power cord should be disconnected before damp wiping. Do 
not use solvents or abrasive cleaners that could damage the surface or printing on the housing. 
 
 

3.2

 

Troubleshooting 

 
Often, supposed defects can be traced back to operating errors. Sometimes other components 
connected to the A 30.3 are also responsible for a malfunction. Before you contact your dealer 
or us about a defect, please check the following list to see if you can correct the malfunction 
yourself, e.g. by resetting the device to the factory settings - see 

RESET

 in section 2.9. 

 

1. No music playback 
 

a) Accidentally switching to stand-by mode via remote control. Press the on/off button (2). 
b) If the display is dark and the operation indicator LED (1) is not lit, the mains fuse may be 
defective.  Since  this  is  usually  caused  by  a  defect  in  the  power  supply  unit  or  amplifier 
electronics (e.g. due to a lightning strike), please contact your dealer. 
c)  The  unit  has  automatically  gone  into  standby  mode  after  a  period  of  20  minutes  without 
playing music or activating a function on the unit (see section 2.10) 

 
2. The device switches off during operation 
 

a)

 

If no music is played for a period of 20 minutes or if a function on the unit is activated, the 
automatic switch-off function of the unit is activated and the unit switches automatically to 
standby mode (see section 2.10 

Automatic switch-off).

 

b)

 

One of the protective circuits of the unit (e.g. overload, overtemperature, short circuit) has 
responded. Please contact your specialist dealer.

 

 

3. Remote control without function 
 

a)

 

The batteries of the remote control are empty. Please replace the batteries (see section 
1.15.1)  

b)

 

There is no direct connection between the remote control and the device or the distance is 
too great. 

 
 
 

 

Summary of Contents for A 30.3





















Reviews: