manualshive.com logo in svg

Avlite AV-OL-KT-I2, Installation & Service Manual

Share
Download
Avlite AV-OL-KT-I2 Installation & Service Manual Download Page 25

AV-OL-KT-I2 - Obstruction Light Kit

Installation & Service Manual

Latest products and information available at 

www.avlite.com

25

5.  Install the MI

Mount the MI light directly to the top of the tower or installation structure either by securing 

it to the mounting plate or by attaching an optional Avlite Right Angle Pole Mounting 

Bracket (for medium intensity fixtures) to the tower and bolting the MI to the bracket.

6.  Mount the top junction box. 

Note:

 

Mounting hardware for junction boxes is not supplied. 

7.  Wire MI to top junction box 

a.  Wire MI power cable to junction box, then data cable to junction box. 

Wiring instructions-Power Cable: 
• 

Connect the black positive conductor from the MI to the +48VDC labelled terminal in 

the top junction box

• 

Connect the white negative conductor from the MI to the -48VDC labelled terminal in 

the top junction box

Summary of Contents for AV-OL-KT-I2













































Reviews:

No comments

Brands by name

Popular brands

Load more brands