AvLab ACEPRO-CEB-8-1 Page 11 User Manual Download

Page: 11 / 36

HDMI 4K HDBaseT Wallplate Kit

⑨

HDMI IN 2 LED:

The LED illuminates yellow when the source device is

connected to the HDMI input 2 port. It will turn green when the HDMI input 2
source is selected as input.

⑩

HDMI IN 2:

Type-A female HDMI input port to connect an HDMI source device.

⑪

FIRMWARE:

Micro-USB port for firmware upgrade.

⑫

PoC IN/HDBT OUT:

RJ45 port to connect the

HDBT IN/PoC

port of receiver by

CATx cable. The transmitter can be powered by this port once the receiver has
been powered up.

⑬

POWER/RS232:

RJ45 port to connect the

POWER/RS232

port on the control

panel via CATx cable to receive RS232 control signal and power the control
panel.

3.2

HDMI 4K HDBaseT Wallplate Receiver

①

FIRMWARE:

Micro-USB port for firmware upgrade.

②

LED indicators:



ON:

The LED illuminates green when the system is in normal working

status.



LINK:

The LED illuminates green when there is a valid HDBaseT connection

with the transmitter. The LED is off when there is no valid link.

HDBT IN/PoC

TO DISPLAY

LINE OUT

IR OUT

DC 24V

TCP/IP

TOUCHSCREEN

FROM

RS232

OUTPUT

CONTROL

MIC

NETWORK

INPUT

MIC

2x20Watt 4

MIC

LINE

REMOTE

MUTE

AUDIO

LINK

HDCP

FIRMWARE

10 11 12 13

Summary of Contents for ACEPRO-CEB-8-1





































Search results

Summary of Contents for ACEPRO-CEB-8-1

Reviews:

Related manuals for ACEPRO-CEB-8-1

Brands by name

Popular brands

AvLab ACEPRO-CEB-8-1, User Manual

Search results

Summary of Contents for ACEPRO-CEB-8-1

Reviews:

Related manuals for ACEPRO-CEB-8-1

Brands by name

Popular brands