AVL 415SE Maintenance Manual Download Page 3 | Manualshive

Page: 3 / 50

AVL 415SE Maintenance Manual Download Page 3

3

Warnings and Safety Instructions

AVL 415SE Smoke Meter — Maintenance Guide

Warnings and Safety Instructions

This manual contains important

warnings and safety instructions

to be

observed by the user.

The product described in this manual is intended for one specific area of applica-
tion which is defined in the instructions. The manual also explains the essential
requirements for the application and operation of the product as well as safety
precautions to ensure smooth operation. AVL can provide no guarantee or
accept any liability for applications other than those described in this manual or
for applications where the essential requirements and safety precautions are not
met.

The product may only be used and operated by qualified personnel capable of
observing the necessary safety precautions. All accessories and equipment
used with the product must be supplied or approved by AVL. The operating prin-
ciple of this product is such that the accuracy of the measurement results
depends not only on the correct operation and functioning of the product, but
also on a variety of peripheral conditions beyond the control of the manufacturer.
The results obtained from this product therefore must be examined by an expert
(e.g. for plausibility) before any action is taken that is based on the results.

All adjustment and maintenance work necessary on instruments when open and
under voltage must be carried out by a professional technician who is aware of
the dangers.

All repairs to the product are to be carried out by the manufacturer or qualified
service personnel only.

When the product is in use, an expert must ensure that neither the test object nor
the testing equipment is operated under conditions that could lead to damage or
injury.

«
1
2
3
4
5
...
»

Summary of Contents for 415SE



















































Reviews:

No comments