manualshive.com logo in svg

AVL 415SE, Maintenance Manual, Page: 27 / 50

Share
Download
AVL 415SE Maintenance Manual Download Page 27

27

Maintenance 

AVL 415SE Smoke Meter — Maintenance Guide

2.3.6 

Reflectometer Head

Glass area

The glass area on the face must not be soiled, scratched or damaged.

1.

Check whether there are any soot deposits or filter paper fibres each time 
you change the filter paper.

2.

Clean the reflectometer head carefully with a puffer and a soft brush, with 
ultra-pure pressurized air, or replace it.

Jacket surface

•

Check the blackening of the visible jacket surface of the inside reflectometer 
head housing between the glass area and the end of the reflectometer 
head. It must be even (no scratches…).

Measuring head

The polymeric material of the measuring head must be clear, transparent and 
colourless - no colouring is allowed. 

•

Replace the measuring head, if the polymeric material is coloured yellowish 
or brownish.

We recommend replacing the reflectometer head every 2 years:

Meas. head N°1 687 224 606
Material number: EZ0104SP

Fig. 13  Reflectometer head

NOTICE

The blackened surface of the housing (inside) and the transparent optical 
surfaces of the reflectometer head must never be scratched.

Fig. 14  Meas. head N°1 687 224 606 (Available in the eSpares

TM

 Webshop)

Summary of Contents for 415SE



















































Reviews:

No comments