8
9.5
Set the laser brightness between 1-100%.
9.6
Select at least one timeslot during which this pattern will be played.
9.7
Finally, press (
) to set up waypoints.
Step 10
The waypoint screen as shown in figure 2.4 will appear:
10.1
To start creating waypoints, first press and drag the joystick
(
) in the center of the window to any direction to start moving
the Motor Platform. For accurate movement, the four
fine-tune buttons (
) on the side of the joystick area can be
used. When, in the top of the screen, (
) is
pressed, the sensitivity of the fine-tune buttons can be adjusted.
Direct the laser towards an area in which it is safe to switch ON the
laser.
WARNING: In the next step, the laser will be switched on. Do not
stare into the laser beam.
10.2
Switch ON the laser by pressing the toggle button (
) to
the right top of the joystick area. After enabling the laser, the
laser brightness can be adjusted at the top of the window and the
joystick button turns green (
).
The laser brightness setting in this window only affects the
brightness during setup, and has no effect on the laser brightness
when the device plays the pattern during normal autonomous
operation (this brightness setting has been defined in Step 9)
10.3
Move the laser to the desired position of the first waypoint and
press the (
) button. Move the laser to the next position and
press the (
) button again. Continue this process until the
desired pattern is created.
After saving the first waypoint in a pattern, the laser can only
move either horizontally or vertically between two waypoints.
Each time a change of direction is required, a waypoint needs to
be saved first.
10.4
To remove a waypoint, select it in the waypoint list on the
bottom of the window. Then press the (
) button. When a
new waypoint is saved, it is always added at the end of the list,
regardless of what waypoint is selected at the time.
10.5
The laser power button (
), which is positioned below the
joystick button (
), can be used to deactivate the laser
between 2 subsequent waypoints. To deactivate the trajectory
between two waypoints, select the first of the two waypoints and
press the laser power button. The waypoint will turn from green to
white in the waypoint list.
Step 6
A list of AVIX Autonomic devices within Bluetooth range will appear.
Select the desired Autonomic and press (
). If no devices are
shown
in the list, move closer to the Autonomic and try again.
The following window will appear:
The connection will be established with the Autonomic (this could
take a moment). If no connection is established after 1 minute, please
refresh the page and try again.
Step 7
After the connection is established, the dashboard screen as shown in
figure 2.1 on page 3 will appear.
4.3 Configuring the device
To start configuration, add at least one timeslot by pressing the
(
) button.
Step 8
After creating at least one timeslot, create a pattern by pressing the
(
) button. The screen as shown in figure 2.2 on
page 3 will appear.
Step 9
After pressing the (
) button the pattern
configuration screen as shown in figure 2.3 on page 3 will appear.
9.1
The pattern is active by default, to deactivate the pattern without
having to remove it, press the toggle button (
) Only active
patterns will be executed.
9.2
Set a pattern name.
9.3
Set a value for cycles between 1 and 10. The amount represents
the number of times the pattern is repeated before the next pattern
is played (if more than one pattern is active within a timeslot).
Example; if ‘Pattern A’ has been set to 1 cycle and ‘Pattern B’ is
set to 3 cycles, and they both are active within the same timeslot,
‘Pattern B’ will be played 3 times for each time ‘Pattern A’ is played
within that timeslot.
9.4
Set the speed between 1-100%.
