Avigilon 2.0C-H5A-PTZ-DC36 Manual Download Page 22 | Manualshive

Page: 22 / 47

background image

Pendant Mount Installation

Camera Package Contents

Note:

The pendant wall mount and pendant NPT mount are sold separately.

Ensure the camera package contains the following:

l

Avigilon H5A-PTZ Pendant Camera

l

T20 star key

l

2 x RJ-45 crimp-on plug

l

Audio, external power, and I/O pigtail cable connector

If you are installing the camera with the pendant wall mount, ensure the package includes the following:

l

Pendant wall mount (IRPTZ-MNT-WALL1 )

l

Mounting template sticker

If you are installing the camera with the NPT mount, ensure the package includes the following:

l

NPT mount (IRPTZ-MNT-NPTA1)

l

Lock nut

l

Thread sealing tape

Installation Steps

Complete the following sections to install the device.

Preparing the Camera for Installation

Note:

Be careful not to scratch the dome bubble.

Pendant Mount Installation

16

«
...
20
21
22
23
24
...
»

Summary of Contents for 2.0C-H5A-PTZ-DC36
















































Reviews:

No comments

Related manuals for 2.0C-H5A-PTZ-DC36

Brand: e-Line Technology Pages: 36

Brand: G-Tech Pages: 14

Brand: IDS Pages: 29

Brand: Olympus Pages: 84

Brand: Olympus Pages: 83

Brand: OM SYSTEM Pages: 266

Linea HS Series

Brand: Dalsa Pages: 74

Brand: IFM Pages: 9

E-P2 - PEN 12.3 MP Micro Four Thirds Interchangeable Lens Digital...

Brand: Olympus Pages: 164

E-P2 - PEN 12.3 MP Micro Four Thirds Interchangeable Lens Digital...

Brand: Olympus Pages: 164

ARTCAM-264IMX-BW-WOM

Brand: ARTRAY Pages: 23

Brand: Rollei Pages: 10

Brand: Abocom Pages: 1

Brand: Polaroid Pages: 15

Brand: Papago Pages: 9

Toy Story DJ016TS

Brand: LEXIBOOK Pages: 48

ATLONA Captivate AT-CAP-FC110

Brand: Panduit Pages: 24

Brand: FujiFilm Pages: 134

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands