manualshive.com logo in svg

Avery Weigh-Tronix AWB 120, User Instructions, Page: 6 / 24

Share
Download
Avery Weigh-Tronix AWB 120 User Instructions Download Page 6

 6

AWB 120 Bench Scale User Instructions

1      

General information and warnings

1.2 Installation

1.3 Electrical installation

1.4 Routine maintenance

Always turn off the machine and isolate from the power supply before starting any 
routine maintenance to avoid the possibility of electric shock.

Make sure that it is placed securely on a flat and level surface.

1.5 Cleaning the machine

1.6 Training

Do not attempt to operate or complete any procedure on a machine unless you have 
received the appropriate training or read the instruction books.

DANGER: RISK OF ELECTRICAL SHOCK. NO USER SERVICEABLE 

PARTS. REFER TO QUALIFIED SERVICE PERSONNEL FOR SERVICE.

DANGER: THE POWER ADAPTOR MUST BE CONNECTED TO A 

SUITABLE ELECTRICAL OUTLET. THE ELECTRICAL SUPPLY MUST 

HAVE A CIRCUIT BREAKER WITH AN APPROPRIATE RATING TO 

PROTECT FROM OVER-CURRENT CONDITIONS.

CAUTION: This equipment must be routinely checked for proper operation and 
calibration.
Application and usage will determine the frequency of calibration required for 
safe operation.

Table 1.1  Cleaning DOs and DON’Ts

DO

DO NOT

Wipe down the outside of standard products 
with a clean cloth, moistened with water and 
a small amount of mild detergent

Attempt to clean the inside of the machine
Use harsh abrasives, solvents, scouring cleaners or 
alkaline cleaning solutions

Spray the cloth when using a proprietary 
cleaning fluid

Spray any liquid directly on to the display windows

Summary of Contents for AWB 120

























Reviews:

No comments