avertX HD458IR User Manual Download Page 47

Page: 47 / 58

37735AA

Trigger Actions

1. Select the

Trigger Actions

tab.

2. Check the boxes to choose the actions that are triggered by a motion detection alarm.

Item

Description

Upload to FTP With Upload to FTP selected, the camera will automatically upload snapshots to the

specified FTP server when an alarm is triggered.

Note:

Make sure you have completed FTP configuration before using this function.

Send E-mail

With Send E-mail selected, the camera will automatically send snapshots to the

specified E-mail address when an alarm is triggered.

Note:

Make sure you have completed E-Mail configuration before using this function.

Record Video to

SD Card

With Record Video to SD Card selected, the camera will automatically record video to

the SD Card when an alarm is triggered.

Note:

Make sure you have completed Storage configuration before using this

function.

Save Snapshot

to SD Card

With Record Snapshot to SD Card selected, the camera will automatically save an

image to the SD Card when an alarm is triggered.

Note:

Make sure you have completed Storage configuration before using this

function.

Record Video to

FTP Server

With Record Video to FTP Server selected, the camera will automatically upload

video to the specified FTP server when an alarm is triggered.

Note:

Make sure you have completed FTP configuration before using this function.

3. Click

Save

Summary of Contents for HD458IR



























































Search results

Summary of Contents for HD458IR

Reviews:

Related manuals for HD458IR

Brands by name

Popular brands

avertX HD458IR, User Manual

Search results

Summary of Contents for HD458IR

Reviews:

Related manuals for HD458IR

Brands by name

Popular brands