background image

19

LONG-TERM BATTERY STORAGE

 If storing your bike from Aventon Bikes for longer than two weeks at a time, follow the instructions below
to maintain the health and longevity of your battery. Charge (or discharge) the battery to approximately 75%
charged.
 DO NOT leave the battery attached to the bike frame. Remove it from the bike during long-term storage.
 Store the battery in a dry, climate controlled, indoor location in between 32 ˚F - 104˚F (0˚C-40˚C). Check
the battery every month, and if necessary, use the Aventon Bike Charger to charge the battery to 75%. 

Please follow the above instructions for storing your bike and battery from Aventon Bikes.
Failure to follow proper battery storage procedures can result in a non-functional battery. 
Replacement will not be convered under warranty.

If the battery is physically damaged, non-functional, performing abnormally, or was dropped
or involved in a crash, with or without obvious signs of damage, please discontinue use and 
charging and contact Aventon Bikes immediately.

DO NOT cover up the charger while it is charging. The charger air cools and needs to be 
on a hard, flat surface in an open space. Use the charger with the indicator light facing upward.
DO NOT use when the charger is inverted, which can inhibit cooling and reduce charger lifespan. 

DO NOT open the battery housing, which will void the warranty and can result in damage to
the battery, property or cause serious injury and/or death.

Summary of Contents for Pace 350 V2
































Reviews: