7
Nose Assemblies
Avdelok® Nose Assembly Selection
Avdelok® nose equipment is available in four types. It is essential that the correct nose assembly is fitted prior to operating the tool.
AVDELOK® NOSE ASSEMBLY SELECTION
Ø
NOSE EQUIPMENT
DESCRIPTION
A
B
C
D
PART N
O.
mm
inch
mm
inch
mm
inch
mm
inch
3/16"
Vertical Flats
21
0.812
16
0.625
54
2.120
25
1.000
07200-02500 *
3/16"
Horizontal Flats
21
0.812
16
0.625
54
2.120
25
1.000
07200-02700 *
1/4"
Vertical Flats
21
0.812
16
0.625
54
2.120
25
1.000
07200-02600 *
1/4"
Horizontal Flats
21
0.812
16
0.625
54
2.120
25
1.000
07200-02800 *
1/4"
Horizontal Flats (Stepped)
21
0.812
16
0.625
54
2.120
25
1.000
07200-03300 *
1/4"
Round
21
0.812
-
-
54
2.120
-
-
07200-03500 *
5/16"
Horizontal Flats
27
1.060
23.6
0.930
91
3.580
40
1.580
07220-02700
5/16"
Horizontal Flats (Stepped)
27
1.060
23.6
0.930
94
3.700
46
1.830
07220-03400
5/16"
Round
27
1.060
-
-
91
3.580
-
-
07220-05600
3/8"
Round
27
1.060
-
-
70
2.750
-
-
07220-02000
3/8"
Round (Stepped)
27
1.060
-
-
74.2
2.920
-
-
07220-03500
3/8"
Short
27
1.060
25.2
0.992
37
1.450
32
1.250
07220-06100
* It is necessary to use adaptor kit (part number 73200-04300) to fit these nose assemblies to the tool.
Stepped anvils give a less severe deformation of the collars thus allowing placing of Avdelok® in softer materials like plastics, wood, etc.
Standard Nose Assembly Selection
The fasteners below can also be placed on the 73200 tool. It is essential that the correct nose assembly is fitted prior to operating the tool.
STANDARD NOSE ASSEMBLY SELECTION
FASTENER
NOSE EQUIPMENT
NAME
Ø
DESCRIPTION
PART N
O.
AVBOLT®
3/16" (4.8mm)
Refer to 07900-00905 datasheet
07220-08100
1/4" (6.4mm)
Refer to 07900-00905 datasheet
07220-07500
5/16" (8.0mm)
Refer to 07900-00905 datasheet
07220-07700 ∆
AVSEAL® II
11mm Standard
For Nose Tip selection refer to 07900-00840 datasheet
07220-06600
12mm Standard
For Nose Tip selection refer to 07900-00840 datasheet
07220-06700
13mm Low Pressure
For Nose Tip selection refer to 07900-00840 datasheet
07220-06600
14mm Low Pressure
For Nose Tip selection refer to 07900-00840 datasheet
07220-06700
16mm Low Pressure
For Nose Tip selection refer to 07900-00840 datasheet
07220-06800 ∆
INTERLOK®
3/8” (10mm)
Standard straight equipment
73200-04500
†
MAXLOK®
1/4” (6.4mm)
Standard straight equipment
*07610-02100
3/16” (4.8mm)
Standard straight equipment
*07610-02000
MONOBOLT®
3/8" (10mm)
Standard Nose Tip
07220-07200
†
∆ Air inlet pressure of 7.0 bar required.
†
Two tool actuations are needed to place these fasteners.
* It is necessary to use adaptor kit (part number 73200-04300) to fit these nose assemblies to the tool.
