Avaya XBU48 Installation And Operator'S Manual Download Page 17

Avaya

t

XBU48 Site Preparation, Installation and Operator’s Manual

S

700071244 Issue 3

13

Chapter 4

Troubleshooting

The 48 Vdc Extended Battery Cabinet is shipped with the battery
charged. However, it may lose some of its charge during shipping and
storage. You can use the XBU48 immediately after unpacking, but it
may not provide the full-rated backup time during a power failure. Upon
initial startup, the XBU48 may need to operate for approximately
24 hours to fully charge the battery and provide full battery-backup time.

Condition

Possible Cause

Action

System does not provide
the expected backup time.

Battery circuit breakers are
in the OFF (O) position.

Switch the battery circuit breaker to the ON (

 | 

) position

for all connected XBU48s.

p

p

The XBU48 is not properly
connected to the UPS.

Verify that the XBU48 cords are connected.

Low battery capacity.

Allow the battery to charge for 24 hours, then retest.

Protected equipment power
requirements exceed UPS
capacity.

Reduce load, then retest.

Charger LED is not on.

XBU48 connections are not
secure.

Verify that the XBU48 is plugged in and turned on.

Charger has failed.

Contact your Avaya service representative.

XBU48 Fault LED is on.

The XBU48 internal
temperature is too high.

Allow the unit to cool. If the condition persists, contact
your Avaya service representative.

Alarm contact is closed.

The XBU48 internal
temperature is too high or
there is an overload
condition.

Allow the unit to cool or reduce the load. If the condition
persists, contact your Avaya service representative.

Battery Service

The battery may be fully
discharged.

Plug the UPS and XBU48 into a power outlet for 24 hours
to charge the battery. After charging the battery, press
and hold the

button for 3 seconds; then check the

indicator.

If the

indicator is still on, see “UPS Maintenance” in

your Avaya UPS operator’s manual.

The battery is not connected
correctly.

Check the battery connections. Call your Avaya service
representative if the problem persists.

Summary of Contents for XBU48





















Reviews: