Avaya J129 Installing And Administering Download Page 10

Page: 10 / 133

Chapter 2: Avaya J129 IP Phone overview

The Avaya J129 IP Phone is a SIP-based IP phone for unified communications. Avaya J129 IP

Phone supports a single line with two call appearances on a dual line display.

Specifications

Specification

Category

Description

Hardware

Display

A graphical LCD display with a
display resolution of 128 x 32 px.

Audio

Supported audio codecs are:

• G.711 A-law/mu-law

• G.726 A

• G.729

• G.729 A

• G.729 AB

• G.722

• OPUS

Softkeys

Three buttons located below the
display.

Switch hook

Magnetic switch-hook.

Handset

Wired handset

Headset

No headset support on Avaya
J129 IP Phone.

Speaker

Hands-free operation

Physical buttons and LEDs

• Dialpad: 0–9, *, #

• Volume:

and

—

buttons

• Mute button

• Hold button

• Phone button

• Speaker button

Table continues…

September 2017

Installing and Administering Avaya J129 IP Phone

Comments on this document? [email protected]

Summary of Contents for J129






































































































































Search results

Summary of Contents for J129

Reviews:

Related manuals for J129

Brands by name

Popular brands

Avaya J129, Installing And Administering

Search results

Summary of Contents for J129

Reviews:

Related manuals for J129

Brands by name

Popular brands