manualshive.com logo in svg

Avaya ERS 8600 series, Configuration Manual

The Avaya ERS 8600 series is a high-performance networking solution designed for large enterprises. Get full control over your network with the Configuration Manual, available for free download from manualshive.com. This manual provides detailed instructions on optimizing your network and maximizing performance.

Share
Download
background image

ERS-8610:5# 

config ipv6 neighbor add ports 4/18 ipv6addr

4040:0:0:0:0:0:0:1 mac 00:80:2d:c0:92:03

Deleting an IPv6 address from the Ethernet SF/CPU slot

You can assign multiple addresses to the Ethernet SF/CPU slot on the Avaya Ethernet Routing

Switch 8800/8600. Delete an address to remove it from the configuration.

Procedure steps

Remove an IPv6 address from the Ethernet SF/CPU slot by using the following
command:

config sys net6-mgmt ipv6 del

 

<IPv6 address/prefix length>

 

cpu-slot

 

<slot-

id>

Variable definitions

Use the data in the following table to use the 

config sys net6-mgmt ipv6 del

 command.

Variable

Value

IPv6 address/prefix length

Specifies the IPv6 address and prefix length
to delete from the port.

slot-id

Specifies the slot number where the port is
located. If a slot ID is not specified, the
address is deleted from the current SF/CPU.

Deleting an IPv6 address

Delete the IPv6 address to stop IPv6 routing.

Procedure steps

1. Delete the IPv6 address on a VLAN by using the following command:

Basic IPv6 configuration using the CLI

110     Configuration — IPv6 Routing

November 2010

Summary of Contents for ERS 8600 series





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ERS 8600 series

B+B SmartWorx UR5i v2 Libratum Start Manual preview
UR5i v2 Libratum
Brand: B+B SmartWorx Pages: 8
B+B SmartWorx ICR-1601 Start Manual preview
ICR-1601
Brand: B+B SmartWorx Pages: 8
Eaton INDGW-X2 Manual preview
INDGW-X2
Brand: Eaton Pages: 10
Paradyne COMSPHERE 3800 Series Release Note preview
COMSPHERE 3800 Series
Brand: Paradyne Pages: 88
Paradyne COMSPHERE 3800PLUS Supplementary Manual preview
COMSPHERE 3800PLUS
Brand: Paradyne Pages: 5
Paradyne Hotwire 6212 Quick Installation Instructions preview
Hotwire 6212
Brand: Paradyne Pages: 2
Watchguard Firebox T15 Quick Start Manual preview
Firebox T15
Brand: Watchguard Pages: 39
Vonets MINI300 Quick Setting Manual preview
MINI300
Brand: Vonets Pages: 8
Multitech MultiConnect SE MTS2EA Specification Sheet preview
MultiConnect SE MTS2EA
Brand: Multitech Pages: 2
Garderos R-7700 Series Operating Manual preview
R-7700 Series
Brand: Garderos Pages: 23
Lutron Electronics Smart Bridge Quick Start Manual preview
Smart Bridge
Brand: Lutron Electronics Pages: 4
Xantech CC12 Installation Instructions preview
CC12
Brand: Xantech Pages: 4
Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV 27-9-2010 Manual preview
E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV 27-9-2010
Brand: Juniper Pages: 122
JUMO 705041 Installation Instructions Manual preview
705041
Brand: JUMO Pages: 60
Patton electronics FORESIGHT 6300 User Manual preview
FORESIGHT 6300
Brand: Patton electronics Pages: 145
SmartBridges airHaul Nexus sB3010 User Manual preview
airHaul Nexus sB3010
Brand: SmartBridges Pages: 80
ADTRAN NetVanta Analog Modem Dial Backup Interface Module Quick Start Manual preview
NetVanta Analog Modem Dial Backup Interface Module
Brand: ADTRAN Pages: 2
Deliberant APC Mach 5 V3 Quick Installation Manual preview
APC Mach 5 V3
Brand: Deliberant Pages: 16

Brands by name

Popular brands

Load more brands