Avaya DEFINITY Server R Manual Download Page 317

Page: 317 / 550

Issue 7 November 2003

6-1

555-233-115

Adding New Carriers and EPN
Cabinets

This chapter provides information on

■

Adding carriers to an r platform in the MCC1 (multicarrier) cabinet

■

Installing or removing EPN cabinets from a DEFINITY ECS

■

Replacing a fan unit.

NOTE:

We recommend that if you are adding carriers and upgrading to a new
software load that you add the hardware before you do the upgrade.

■

Add MCC Port Carriers

■

Add a Control Carrier (Add Duplication)

■

Add Center Stage Switch

■

Add a Switch Node Carrier

■

Install a New EPN Cabinet in an Existing System

■

Remove an EPN Cabinet from an Existing System

Summary of Contents for DEFINITY Server R







































































































































































































































































































































































































































































































































































Search results

Summary of Contents for DEFINITY Server R

Reviews:

Related manuals for DEFINITY Server R

Brands by name

Popular brands

Avaya DEFINITY Server R, Manual

Search results

Summary of Contents for DEFINITY Server R

Reviews:

Related manuals for DEFINITY Server R

Brands by name

Popular brands