Avaya CPSEE_TSP500 User Manual Download Page 109

Page: 109 / 216

Chapter 5 Admin Terminal Commands

CPSEE_TSP500 User Guide

Version 4.0

Page 5-39

This document is confidential and proprietary to SER Solutions and is not for external use.

SYSLOG

The

syslog

command is similar to the

install

options

command because it

allows setting hexadecimal bits to control what messages are sent to the
TspLogger.

The following shows the output of the “syslog command”.

Syslog Options = 207f

Table 5-26: STATUS Command.

Command

Description

CAMP TYPE

Outbound, Inbound, or Validation.

LOGGED IN

Count of Agents currently logged in on this Cam-
paign.

WAITING

Count of Agents waiting for calls.

TALKING

Count of Agents talking on calls.

TEL NUMBS

Count of telephone waiting to be dialed.

DIALS

Count of current Dials for this Campaign.

RING TIME

Average time the phone rang before called party
answered.

WAIT TIME

Average (short term) time agents are waiting for
calls.

ACC DIALS

Total Dials.

CONNECTS

Total Answered calls.

ABANDONED

Total Abandoned Calls.

RNA’S

Total Ring No Answers.

BUSY’s

Total Busy Calls.

DIAL FAIL

Total Dial failures.

INCOMPS

Total Incomplete Dials.

MODEMS

Total Fax or Modems.

UNKNOWNS

Total Unknown SIT tones detected.

CNG_NUMS

Total (IC) type SIT Tones detected.

TRAFFIC

Total (NC) type SIT Tones, or Fast Busy detected.

OOS

Total count Trunks went Out of Service dialing on
this Campaign.

ANS_MACH

Total Answering Machines detected.

Summary of Contents for CPSEE_TSP500

























































































































































































































Search results

Summary of Contents for CPSEE_TSP500

Reviews:

Related manuals for CPSEE_TSP500

Brands by name

Popular brands

Avaya CPSEE_TSP500, User Manual

Search results

Summary of Contents for CPSEE_TSP500

Reviews:

Related manuals for CPSEE_TSP500

Brands by name

Popular brands