Figure 63: Test Carrier (T) screen
Tests can be performed once, for one through 98 minutes, or continuously (selected by entering
99 minutes), until a
Stop Test
command is entered. Tests continue for the duration specified
even if a failure occurs, and terminate at the end of the time period or when a
Stop Test
command is issued. Only
Stop Test
stops a test with a duration selection of 99; however,
the
STOP
command terminates a test set to any duration from one to 99. After entering the test
number, a prompt similar to
Figure 64: Test parameters screen
on page 240 appears.
Figure 64: Test parameters screen
Before a test is run, be sure to verify that the card is disabled, as the tests interfere with calls
currently in process.
During a test, if an invalid word is received, this is recorded by a failure peg counter. The peg
counter has a limit of 65,000. At the end of the test, the Test Results message indicates how
many failures, if any, occurred during the test.
on page 240 shows which test to run for the associated equipment.
Table 99: MMI Tests
Test number
Equipment Tested
Test Description
1
LEI
Local loopback
2
E1 link, LEI, and E1 network
External loopback
3
CPE device and E1 network
Network loopback
Test 1, local loopback, loops the E1 link signaling toward itself at the backplane connector. Test
data is generated and received on all timeslots. If this test fails, it indicates that the LEI is
defective.
Figure 65: MMI Local loopback test
on page 241 illustrates how the signaling is
looped back toward itself.
NT5D33 and NT5D34 Lineside E1 Interface cards
240 Circuit Card Reference
July 2011
Summary of Contents for 1000 Series
