background image

and belt towards you. Turning the hex key clockwise pushes the 

rear roller and belt away from you.   

Maintenance Instructions 

WARNING! Before performing any maintenance to your treadmill, 

always unplug the power cord from the grounded outlet.   

CLEANING: Routine cleaning of your treadmill will extend the life of 

your unit. WARNING! To prevent electrical shock, be sure the unit 

is unplugged from the wall electrical outlet before attempting any 

cleaning or maintenance.   

AFTER EACH WORKOUT: Wipe off the console and other 

treadmill surfaces with a clean, water damp-ened soft cloth to 

remove excess perspiration. USE NO CHEMICALS.   

WEEKLY: Use of a treadmill mat is recommended for ease of 

cleaning. Dirt from your shoes contacts the belt and eventually 

makes it to underneath the treadmill. Vacuum underneath treadmill 

once a week. 

  DECK LUBRICATION: The walking belt has been pre-lubricated 

at the factory. However, it is recom-mended that the walking board 

be checked periodically for lubrication to ensure optimal treadmill 

perfor-mance. Every 30 days or 30 hours of operation, lift the sides 

of the walking belt and feel the top surface of the walking board as 

Summary of Contents for AT480























Reviews: