Avante HED102D Lift Assembly Instructions Download

Page: 2 / 3

Press and display real height

Press until 1 appears, release the button, it runs
to corresponding height and displays current position.

Press until 2 appears, release the button, it runs
to corresponding height and displays current position.

Press until 3 appears, release the button, it runs
to corresponding height and displays current position.

Over-heating

protection

Sensorless

alarm

Overload
protection

Rebound
protection

Overvoltage

alarm

Undervoltage

alarm

Step out alarm

Breaking

protection

Metric and

English

unit conversion

Hot: it alarms when continuous working 2 minutes;
clear automatically after resting 18 minutes.

E1: It alarms when motor hall value cannot be inspected;
clear it after press reset or re-power on.

E2: overload alarm when running up, clear automatically
after 3 seconds; overload alarm when running down,
clear it after press reset or re-power on.

E02: it alarms in reversed compression when running;
clear automatically after rebound 4cm; or press any
button to clear when rebounding.

E03: it alarms when voltage is higher than limit value,
clear automatically after voltage reduced to set value.

E05: it alarms when voltage is lower than limit value;
clear automatically after voltage is higher than set value.

E06: it alarms when height difference between left and
right leg exceeds set value; disconnect power supply for 1
minute to clear error.

It stops and enters protection state when motor lines or
manual control lines are removed or disconnected
accidentally; back to normal after reconnected and alarm
cleared.

Press for 3 seconds and it will display ---, release ,
press until 1 appears, release the button and it
displays current height. (English unit)

Press for 3 seconds and it will display ---, release ,
press until 0 appears, release the button and it
displays current height. (metric unit)

Protection mode (auto lock screen mode)

Press until 4 appears, release the button, it runs
to corresponding height and displays current position.

Save button,used to enter the save height function

After press , the interface flashes and set memory
position, press until H1 appears, release button and
it displays current height.

INSTALLATION

Install the side plate (3) and use the wrench (E)
to lock the screw (B)

Insert the connecting rod (7) into the frame (5) .

Adjust the distance according to the size of the table,
and then tighten the screw (B) with the wrench (E).

Mount the desktop (1) with screws (A) on the two side plates

Mount the control box(10) under desktop(1) with screws (A).
Use the screws (D) to install the controller panel(2) under
the desktop (the right or left side of the desk can be chosen
to mount the control box)

OPERATION

1080-1870mm

M5x16

8PCS

A
M5x16 2PCS

M5x12 2PCS

M6x12

8PCS

M6x12

8PCS

Reset

Memory
Position

in condition of E2 or run to basic height position, long
press for 5 seconds, display RES and press still, it
goes down to the lowest and rebound certain height,
reset finish and show basic height.

3 4

ANTE

Summary of Contents for HED102D Lift

Page 1: ...ble legs Foot Controller box 1 2 3 4 5 6 7 8 9 10 1pc 1pc 2pcs 1pc 2pcs s c p 2 2pcs 2pcs 1pc 2pcs Adjustable feet M5 16 screw M6 12 screw M5 12 screw Screws Fasteners bag Desk Parts A B C D E 2pcs S...

Page 2: ...nd enters protection state when motor lines or manual control lines are removed or disconnected accidentally back to normal after reconnected and alarm cleared Press for 3 seconds and it will display...

Page 3: ...plied by a general merchandise retailer that may not be familiar with your specific application or description of application Be sure to attain third party approval from a qualified specialist for you...

Search results

Summary of Contents for HED102D Lift

Reviews:

Related manuals for HED102D Lift

Brands by name

Popular brands

Avante HED102D Lift, Assembly Instructions

Search results

Summary of Contents for HED102D Lift

Reviews:

Related manuals for HED102D Lift

Brands by name

Popular brands