Avante FURMDKAVNAH12 User Manual Download Page 9

Page: 9 / 12

Motorised Height Adjustable Desk

E&OE

Operation

Control Panel

Control

Description

Display

Shows current height or other information, such as when a reset is required or when saving

a pre-set height etc.

▲

Raise desk height. Press and hold, then release when required height is reached.

▼

Lower desk height. Press and hold, then release when required height is reached.

Press to

go to pre-set height

"1".

Press to

go to pre-set height

"2".

Press to

go to pre-set height

"3".

Press to

save a pre-set height

Press to activate the

reminder timer

Functions and Using the Desk

To use the desk:
1. Connect the supplied electrical cable to the motor control module, and at the other end to a grounded

240VAC / 50Hz mains electrical supply.

2. Switch the electrical supply ON at the power outlet.
3. The control panel will illuminate – the desk is ready to use.

Resetting

Before using the desk, you must "reset" it – resetting means that the motor control module needs to "know"

when the legs are at the lowest position, as a reference.
Press and hold "

▼

" on the control panel – the desk will lower. Once reaching the lowest position, the motor

wil

l stop. Continue pressing ▼. The desk will

then rise approximately 5mm to an indicated height of "

75.0

" or

a similar number (approximately 75cm form the top of the desk to ground level). Once this occurs, release

▼

. The desk can now be used.

Adjusting Height

The motor has a "duty cycle" of 2 minutes per 20 minutes. This means that the desk can be raised or

lowered continuously for approximately 2 minutes. After this time, the motor must be allowed to cool

for approximately 18 minutes before being used again to raise or lower the desk.

To raise the desk, press and hold

▲

until the desired height is reached. To lower the desk, press and hold

▼

until the desired height is reached. The actual height from the top of the desk to ground level is shown in the

display.

ANTE

Summary of Contents for FURMDKAVNAH12













Search results

Summary of Contents for FURMDKAVNAH12

Reviews:

Avante FURMDKAVNAH12, User Manual, Page: 9 / 12

Search results

Summary of Contents for FURMDKAVNAH12

Reviews: