background image

10 (28) 

CAUTION

 

Risk of thrown objects, loss of stability, and damage to the the equipment - Use the 
Stump grinder only for its intended purpose.

  Using the stump grinder for other 

purposes than grinding down short tree stumps can cause hazardous ejection of material, 
dust, or damaged machine parts. 

3.1

 

Safe shutdown procedure 

Safe stopping of the attachment, before going near the attachment: 

WARNING:Always stop the attachment following safe stopping procedure 

before leaving the driver's seat. 

Safe stopping procedure prevents all 

unintentional movements of the attachment. Note that the loader boom can move 

down even if the engine of the loader is turned off. Safe stopping procedure: 

Lower the boom and the attachment on the ground.

Shut down the loader engine and lock the parking brake.

Release residual pressure from the hydraulic system; move all hydraulic control

levers to their extreme positions a couple of times.

Prevent starting of the machine, remove ignition key.

3.2

 

Personal protective equipment 

Remember to wear proper personal protective equipment: 

The noise level at the driver's seat may exceed 85 dB(A) depending on loader

model and operating cycle. Extended exposure to  loud noise can cause

hearing impairment. Wear hearing protection while working with the loader.

Wear protective gloves.

Wear safety boots whenever working with the loader.

Wear safety glasses when handling hydraulic components.

Summary of Contents for A37265





























Reviews: