background image

14 (22) 

 

 

 

 

5.1.2

 

Installing the rear brush 

The loader can be equipped with a rear brush. With the rear brush the surface is sweeped once again in order 

to avoid leaving any tyre marks when leveling the infill and finishing the surface. 

 

 

Installing the rear brush 

Attaching the attachment on the rear of the loader is quick and easy, but it must be done carefully. Lifting 

equipment is necessary due to the weight of the attachment. 
1.  Lift the attachment e.g. with an 

overhead crane or equivalent. Fasten 

the hoisting sling to the lifting point as 

shown in the adjacent figure. 

 

 

 

2.  Mount the attachment to the rear of the 

loader by using existing fixing points. If 

there are additional rear weights at the 

rear of the loader they must be 

removed. 

 

3.  Fix the rear brush with screws to the 

loader as shown in adjacent figure. Use 

thread locking compound. 

 

4.  Use threading taps for rethreading the 

screw threads before fastening the 

screws, if necessary. 

 

 

 

 

 

WARNING

 

Risk of crushing -  Going under a lifted attachment can cause serious injury or 
death.

 Do not allow anyone stand under the lifted load. Always make sure that it is safe 

to move the lifted load. Move the lifted load carefully and calmly. 

 

 

 

 

 

 

 

 

 . 

 

Summary of Contents for A37035























Reviews: