background image

10 (32) 

 

 

 

 

 

Remember to wear proper personal protective equipment: 

 

 

The noise level at the driver's seat may exceed 85 dB(A) depending on loader 

model and operating cycle. Extended exposure to loud noise can cause 

hearing impairment. Wear hearing protection while working with the loader. 

 

 

Wear protective gloves. 

 

 

Wear safety boots whenever working with the loader. 

 

 

Wear safety glasses e.g. when handling hydraulic components. 

 

.. 

 

 

Safe stopping of the attachment, before going near the attachment: 

 

 

WARNING

 

Always stop the attachment following safe stopping procedure before leaving 

the driver's seat. 

Safe stopping procedure prevents all unintentional movements of 

the attachment. Note that the loader boom can move down even if the engine of the 

loader is turned off. Safe stopping procedure: 

 

Lower the boom and the attachment on the ground. 

 

Shut down the loader engine and lock the parking brake. 

 

Release residual pressure from the hydraulic system; move all hydraulic control 

levers to their extreme positions a couple of times. 

 

Prevent starting of the machine, remove ignition key. 

 

 

Summary of Contents for A35965

































Reviews: