background image

 

 

15 (24) 

 

 

6.

 

Instructions for use 

Practise the use of the attachment and the controls of the loader in a safe area. If you are unfamiliar with the 

particular loader model, it is recommended to practice its use without any attachments. 

 

 

 

 

WARNING

 

Risk of tipping over - Avoid overload. 

Loader can tip over 

when handling too heavy loads, or because of dynamic 
movements caused by driving with and handling of a heavy 
load. Do not extend the telescopic boom when the load 
approaches the lifting capacity of the loader, or when the 
loader boom is in horizontal position. When you notice that 
the rear wheels of the loader are about to lift from the ground, 
or if the load indicator of the loader (if fitted) signals: 

 

 

 

 

Lower the load calmly and retract the telescopic boom 

 

Avoid sudden changes in speed or direction whenever load is lifted 

 

Use additional counterweights as needed 

 

 

.. 

 

 

 

 

WARNING

 

Risk of falling from height and crushing under bucket or 
loader  -  Never use a bucket as a lifting platform or to 
carry people.

 Never use the loader or its attachments to lift 

persons or as any kind of work platform even temporarily. 
Never climb on the attachment. 

Always lower the bucket on the ground before leaving the 
driver's seat. The loader is not intended to hold loads lifted for 
longer periods of time. 

 

 

 

  

 

 

6.1

 

Checks before use 

  Ensure that bystanders are at a safe distance when operating the equipment. Do not let anyone to 

enter danger area of the boom or to stay directly in front of the loader. Also make sure that it is safe to 

reverse with the loader. Never assume that bystanders will remain where you last saw them; 

especially children are often attracted to the moving equipment. 

  Check the  general condition of the attachment and the loader, and check for possible hydraulic oil 

leaks. The attachment must not be used, if there is a fault in the hydraulic system of the loader or the 

attachment. Refer to Chapter 7 for maintenance instructions. 

  Operate the attachment and the controls of the loader only when seated on the driver’s seat. Ensure 

that the loader and the attachment are used in a safe manner and as intended. Do not allow children 

to operate the equipment. 

  Never operate the loader or attachments while under the influence of alcohol, drugs, medication that 

may impair judgement or cause drowsiness, or if not otherwise medically fit to operate the equipment. 

  Remember correct working methods and avoid leaving the driver’s seat unnecessarily. 

 

 . 

 

Summary of Contents for A21273

























Reviews: