background image

34

400 Series

Hydraulic oil cooler fan fuse

The red indicator no. 18 on the dashboard indicates blown 
hydraulic oil cooler fan fuse. If the indicator is lit, check 
the 25A fuse of the oil cooler fan. Contact Avant service 
if necessary.

Jump start and auxiliary power

The engine can be started with auxiliary power if necessary, 
by using appropriate (strong enough) jump start cables. 
Connect first one end of the positive cable to the positive 
(+) post of the dead battery. Then connect the other end 
of the positive jumper cable to the positive (+) post of the 
charged battery. Connect one end of the negative jumper 
cable to the negative (-) post of the charged battery. Then 
connect the other end of the negative jumper cable to 
a solid, non-paint coated metal part of the engine of the 
dead loader, as far from the dead battery as possible.

Read Operators Manual of the vehicle that is 
giving auxiliary power, in order to make sure that 
the vehicle suited for that. The vehicle can get 
damaged when giving auxiliary starting power.

Never bypass battery or connect cables directly 
to starter motor. Engine may get damaged.

Storage of the machine

Before long term storage clean the loader carefully and 
check and touch-up painted surfaces if necessary in order 
to avoid rust damages. Grease the greasing points and put 
oil on piston rods of the cylinders. Take off the battery and 
store it in the right way. It is recommended to perform the 
yearly service before storage. Store the machine indoors 
if possible. If outdoors storage is necessary, protect the 
machine with the designated cover (part no. 65478). See 
the engine owner’s manual to prepare the engine for long 
term storage and how to start it after long storage period.

Refueling

Check fuel level and fill the tank if necessary. Make sure 
to add fuel before the fuel tank gets empty. Should this 
happen, a manual bleeding must be performed before 
restart. If possible, refuel the loader after use to prevent 
condensation of water into the fuel tank. 

Use only clean fuel and take care when refueling 
the loader to avoid dirt and water from entering the 
fuel tank. Clean fuel cap and surroundings before 
opening the cap. Always store fuel properly in an 
approved container. Water in fuel can cause severe 
damage to engine injection system.
Always stop the engine and allow it to cool before 
refueling. Do not spill fuel when refueling. Should 
this happen, wipe the fuel away immediately 
in order to avoid risk of fire. Keep fuel away 
from sources of ignition. Do not smoke during 
refueling. 

Check all fuel lines for tightness and wear on a regular 
basis. Tighten or repair them as needed. Check fuel system 
thoroughly and clean the fuel tank after every 2 years.

Metal structures of the loader

Contact Avant service in case the steel structure 
of the loader gets damaged. A faulty reparation 
can cause a dangerous situation.

In case the ROPS safety frame or the FOPS canopy 
of the machine gets damaged, the machine must 
be taken to Avant service for checking. It is not 
allowed to repair the ROPS and FOPS.

Service and maintenance instructions

Summary of Contents for 400 Series









































Reviews: