background image

4

Practical connections of the evaluation board using a power MOSFET for an actual inverter test

1.  Solder actual power MOSFETs at Q1 (or Q2) for the top and bottom arms of the half-bridge inverter isolated drivers.
2.  Connect a +5V DC isolated supply1 5V and GND terminals of CON1 for both arms of the isolated drivers.
3.  Connect another isolated DC supply2 (voltage range from 12 V ~ 20 V) across V

CC2a

 and V

EEa

 at pin 7 and pin 5 of IC2a 

respectively for the bottom arm.  

4.  Connect the signal output (meant to drive the bottom arm of the half-bridge inverter) from the microcontroller to 

Signal Input 1 across pin IN1+ and IN1- of CON1a of the bottom inverter arm isolated driver.

5.  Connect the signal output (meant to drive the top arm of the half-bridge inverter) from the microcontroller to Signal 

Input 2 across pin IN2+ and IN2- of CON1b of the top inverter arm isolated driver. Note: Signal Input 2 should be 

180

°

 out of phase w.r.t. Signal Input 1.  Check that V

CC2b

 (voltage close to V

CC2a

) is generated through the bootstrap 

components D3b and R6.

6.  Use a multi-channel digital oscilloscope to capture the waveforms at the following points:

a.  LED signal at IN1+ pin w.r.t. GND for the bottom arm.
b.  LED signal at IN2+ pin w.r.t. GND for the top arm.
c.  Vga for the gate driving voltage of Q1a (or Q2a) w.r.t. V

Ea

 of the bottom inverter arm (differential probe needed).

d.  Vgb for the gate driving voltage of Q1b (or Q2b) w.r.t. V

Eb

 of the top inverter arm (differential probe needed).

7.  Connect a power cable from the output pin (marked Load) to the inverter load.
8.  Connect the high voltage cables from the top arm power MOSFET drain pin to HVDC+ and from the bottom arm 

power MOSFET source pin to HVDC-, respectively, as shown. (Note: It is recommended that you enable the current-

limiting function of the HV power source supplying the high voltage DC bus voltage during this test to protect the 

inverter and its driver circuitries).

Microcontroller

IN1+
IN1- Signal Input 1

+5V

GND

DC Supply1

IN2+
IN2- Signal Input 2

 Power 

MOSFET

mounted

1

1

2

3

12~20 V

+

DC Supply2

4

5

12~20V

+

5

6a

6b

6c

6d

Load

7

HVDC+

HVDC

8

8

Power 

MOSFET

mounted

Figure 4. Connection of evaluation board in actual applications

Summary of Contents for ACPL-P346










Reviews: