AuviTran AVM500-ES User Manual Download Page 52

Page: 52 / 52

Auxiliary Power Supply – Firmware Update

AUXILIARY POWER SUPPLY

AVM500-ES provides another source of power supply, to improve the reliability of the system. It allows you to have two

distinct power supply sources, for redundancy solutions. When both power supply units (PSU) are plugged, AVM500-ES

compare them, and always choose the best. In case of failure of one PSU (or associated electrical network), AVM500-ES will

so continue to work.

Auxiliary PSU (ref. AVPSAUX-E45/EB) is validated and provided by AuviTran only. Please contact us if you want to integrate

the redundant PSU in your system.

http://www.auvitran.com

FIRMWARE UPDATE

To upgrade your AVM500-ES with new firmware release, please download the ES-Firmware Updater software on AuviTran’s

web site. You can also check periodically on the web site for new firmware release.

Please follow the steps below to put your device into a coherent mode for firmware upgrade.

First of all, unplug all devices that may be connected to the AVM500-ES, and plug your computer on port
{Ain}.

Then, ensure that all {B, C, D, E} ports are not dissociated (via ES-Monitor). In this case, the firmware

updater won’t be able to access to the devices. If needed, re-associate ports. For AVM500-ES/3Ports,
only ensure that ports B and C are not dissociated.

Save to non-volatile memory by clicking the

icon in ES-Monitor. You will have to re-set your

previous configuration after the update, and save it again with the same icon.

Finally, put dip switch #1 to “ON”.

You are now ready to upgrade the device properly and at a maximum speed. Please read the ES-Firmware Updater manual
to handle it properly.

AVM500-ES User’s Manual v2.1

AuviTran 2010

Summary of Contents for AVM500-ES





















































Search results

Summary of Contents for AVM500-ES

Reviews:

Related manuals for AVM500-ES

Brands by name

Popular brands

AuviTran AVM500-ES, User Manual

Search results

Summary of Contents for AVM500-ES

Reviews:

Related manuals for AVM500-ES

Brands by name

Popular brands