background image

P.2

 Installation 

Guide

 AS-6205 SH 

Table of Contents 

Introduction ..................................................... 3
Included in the Package ................................. 3
Before You Get 

Started

…............................... 4

Installation Points To Remember ................... 4
Harness Description ....................................... 4

6-Pin Main Ignition Harness ....................... 5
5-Pin Secondary Harness........................... 5
12-Pin Accessories Harness ...................... 6
2-Pin Harness ............................................. 8

Flashing the Hood Pin .................................... 9

What is 

Flashing

the Hood Pin? ................ 9

The Programming Assistance Button (A.k.a. 
PAB.) ............................................................ 10
How to Program the Transmitter. ................. 10
How to Enter Options Programming Mode... 10
Options Programming................................... 11

Horn Honk / Siren Timing (Optional) ........ 12

Auto Tach

 Programming Procedure........ 13

Multi-Speed Tach Programming................... 14
Testing .......................................................... 14
Closing Up .................................................... 15
Supplementary Information .......................... 15

Fifth Relay Output (2

nd

 IGN or 2

nd

 ACC or 

2

nd

 START)............................................... 15

Ignition-Controlled Door Locks ................. 16
Secure Lock.............................................. 16
Turbo Mode .............................................. 16
Safe Start (Child Safety Mode)................. 17
Siren or Horn Chirps................................. 17
Vehicle Type – Gas Or Diesel .................. 17
Passive Or Active Arming......................... 17
Disarmed Notification ............................... 18
Two-Stage Disarm.................................... 18
Shock Sense Bypass ............................... 18

Resetting The Module .................................. 18
Events Logging............................................. 18

Events playback ....................................... 18
Start Failure Codes via Parking Lights ..... 18
Intrusion Codes ........................................ 19

Intrusion Codes via LED light ....................... 19
Chirps ........................................................... 19
Diagnostics - Parking Lights Flash Rate ...... 20

Summary of Contents for AS-6205 SH





















Reviews: