IV. Programming Options
The AS-6105 SH/SR system, is equipped with three custom programming menus that allow the installer to custom-fit
the system outputs according to installation requirements.
The Options are designed to facilitate interfacing with all vehicle types.
To get into a Programming Mode, proceed as follows:
1.
Ensure that the Hood is up and that the Ignition is
OFF
.
•
Hold the Hood Pin-switch down for 4 seconds.
•
Release the Pin-switch.
The Parking Lights will come on.
•
While the Parking Lights are on, immediately push and release the Pin-switch again.
The Parking Lights will stay on for up to 20 seconds
.
2.
Press and hold the Brake Pedal, then press one of the following buttons on the Transmitter (see Transmitter
Functions on page 7 for button layout):
•
LOCK
to enter Mode 1;
•
UNLOCK
to enter Mode 2;
•
TRUNK
to enter Mode 3.
The Parking Lights and the Siren will flash and chirp once, twice or three times to confirm entry into a Mode.
3.
Release the Brake Pedal.
The Programming Menu will automatically start at Function 1. Once you select one of the Options of Function 1, you
will automatically move to the next Function. To select one of the four Options of a given Function, press the
corresponding button on the Transmitter (see Transmitter Functions on page 7 for button layout):
•
LOCK
button
= Option 1
•
UNLOCK
button = Option 2
•
TRUNK
button = Option 3
•
START
button = Option 4
In each Function, once an Option has been selected the Parking Lights will flash 1, 2, 3 or 4 times (depending on the
selected Option).
Please note
that, unlike Options within a Function, Functions within a Mode can only be accessed sequentially: the
Programming Menu will move from Function 1 to Function 2, 3, an so on. Therefore, whenever you enter a particular
Mode, be prepared to re-configure all the Functions of that Mode in ascending order.
MODE 1
* INDICATES DEFAULT SETTING
FUNCTION 1 – Ignition-controlled Door Locks
OPTION 1*
Ignition Lock
ENABLED
OPTION 2
Ignition Lock
DISABLED
OPTION 3
Ignition
LOCK ONLY
OPTION 4
Ignition
UNLOCK ONLY
FUNCTION 2 – Secure Lock
OPTION 1*
Secure Lock
DISABLED
(1-sec. Disarm pulse)
OPTION 2
Secure Lock
ENABLED
in Smart Mode
OPTION 3
Secure Lock
DISABLED
(0.5-sec. Disarm pulse)
OPTION 4
Secure Lock
ENABLED
in Standard Mode
FUNCTION 3 – Door lock pulse timing
OPTION 1*
7/10-sec. Lock/Unlock pulses
OPTION 2
4-sec. Lock/Unlock pulses
OPTION 3
7/10-sec. Lock pulse and two 1/10-sec. Unlock pulses
OPTION 4
1/10-sec. Lock/Unlock pulses
FUNCTION 4 – AUX 3 Programming
OPTION 1*
Constant while the
TRUNK
button is pressed and Data out
OPTION 2
1-sec. Trunk 1 output when
TRUNK
button is pressed for 3 sec. with Ignition
OFF
or under remote run
OPTION 3
Trunk 2 output with Disarm/Rearm pulses
FUNCTION 5 – AUX 2 Programming
OPTION 1*
Priority Door Access on 2
nd
UNLOCK
and each subsequent Unlock, and Car Finder
OPTION 2
Toggle
ON/OFF
with 30-second timeout
OPTION 3
Constant output while the button is pressed
OPTION 4
Priority Door Access on 2
nd
Unlock, and Car Finder
MODE 2
* INDICATES DEFAULT SETTING
FUNCTION 1 – Home Valet Mode
OPTION 1
Home Valet
ENABLED
P. 2
Quick Installation Guide
AS-6105 SH/SR
OPTION 2*
Home Valet
DISABLED
